As an Amazon Associate I earn from qualifying purchases.
1. Aideepen #ad
10PCS TTP223 Capacitive Touch Switch Button Self-Lock Module for Arduino #adAideepen #ad
- Modes: jog, self-locking. The module is based on a touch-sensing IC TTP223 capacitive touch switch module. Power supply:2. 5v-5. 5v. Module size:15mm*11mm. Package content:10pcs aideepen TTP223 Capacitive Touch Switch Sensor.
2. HiLetgo #ad
HiLetgo CAP1188 8 Key Capacitive Touch Sensor Module SPI I2C Captouch LED 8 Button 8 Keys Interfaces 3V-5V for Arduino #adHiLetgo #ad
- Cap1188 8 key capacitive Touch Sensor Module. Support for both i2c and SPI, so it easy to use with any microcontroller. Spi i2c captouch led 8 button 8 Keys Interfaces 3V-5V.
3. AiTrip #ad
10 Pack TTP223B Digital Touch Capacitive Sensor Switch Module DIY for Arduino Raspberry Pi #adAiTrip #ad
- In the normal state, the module output high, low power consumption, the module output low, but when a finger touches the corresponding position, if not touched for 12 seconds, switch to low-power mode.
Allows you to remove the worry of conventional push-type keys. Module can be installed in such as surface plastic, glass of non-metallic materials. This module is capacitive type jog mode touch switch module that is based on a touch detection IC TTP223B.
You can put to a thin paper non-metallic cover the surface of the module, when touch the correct location of the module, that you can put it hidden in the walls, desktops and other buttons.
Feature：ttp223b chip, low power consumption, vcc, sig; both positive and negative can be used as a touch surface, and it is bright when power on right; control port: gnd, and power supply is DC 2-5.5v; green led indicator, and replace the traditional touch of a button.
4. DFROBOT #ad
DFRobot Gravity: Digital Capacitive Touch Sensor for Arduino #adDFROBOT #ad
- This little sensor can "feel" people and metal touch and feedback a high/low voltage level. This digital capacitive touch sensor for arduino provides a one-touch style switch on your project.
Even isolated by cloth or paper, it still can feel the touch. It uses the most popular capactiive sensing technology which is the same as your mobile phone.
5. WMYCONGCONG #ad
WMYCONGCONG 10 PCS TTP223B Digital Touch Capacitive Sensor Switch Module DIY for Arduino 10PCS #adWMYCONGCONG #ad
- Size: 24 x 24 x 7mm/9. 45 x 9. 45 x 2. 76inch l x W x H. Low power consumption. Great replacement for the traditional touch of a button. Power supply: 2 - 5. 5v dc. 4 m2 screws positioning holes for easy installation.
6. Tegg #ad
Tegg TTP229 1PC 16 Channel Digital Capacitive Switch Touch Sensor Module for Arduino Electronic DIY Tool #adTegg #ad
- 16-key board ttp229 capacitive touch sensor IC. Working voltage: 2. 4v-5. 5v. The module can be set to output mode, the key output mode, the longest time and fast output / low power options.
Pcb board size: 64. 5x49. 5mm/2. 54x1. 95lxW. Package Included:1PC. High quality, durable and have along life.
7. CenryKay #ad
CenryKay TTP223B Capacitive Digital Touch Sensor Touch Button Module for Compatible Arduino10PCS #adCenryKay #ad
- 4 m2 screw positioning holes for easy installation. Jog type: the initial state is low level, S outputs a high level and the light is on; when the hand is released, when touched by hand, it is a low level; Level.
Low power consumption. Power supply: 2-5. 5v dc. Size: 24 x 24 x 7mm / 9. 45 x 9. 45 x 2. 76inch l x W x H. Both sides can be used as touch surface, which can replace traditional touch keys.
8. Youliang #ad
Youliang 2pcs Touch Capacitive Sensor Switch Module #adYouliang #ad
- Both the front and the back can be used as the touch surface, which can replace the traditional touch button. Touch area: the internal area of an icon similar to a fingerprint, which can be triggered by a touch of a finger.
Control interface: a total of 3 pins gnd, vcC is power supply, GND is ground, SIG, vcc, SIG is digital signal output pin.
Power indicator: green led, lights up when power is on correctly; power supply can be 2-5. 5v dC. Positioning hole: 4xm2 screw positioning holes, with a hole diameter of 2. 2mm, to facilitate the installation and positioning of modules and realize the combination between modules.
9. SUBALIGU #ad
SUBALIGU 10pcs TTP223B Capacitive Touch Switch Module Touch Sensor Switch Digital Capacitive Touch Sensor Switch DC 2~5.5V Compatible with Arduino Raspberry Pi #adSUBALIGU #ad
- In addition to the thin paper non-metallic covering the surface of the module, as long as the correct location of the touch, you can make hidden in the walls, desktops and other parts of buttons.
In the normal state, the module output low, low power consumption; When a finger touches the corresponding position, the module output high, if not touched for 12 seconds, switch to low-power mode. This is the "momentary" variety of the touch sensor - touch and it turns on, release and it turns off.
Four m2 screws positioning holes for easy installation. Module can be installed in such as surface plastic, glass of non-metallic materials. Positive and negative can be used as a touch surface, can replace the traditional touch button. The module is based on a touch-sensing ic ttp223b capacitive touch switch module.