As an Amazon Associate I earn from qualifying purchases.
1. SainSmart #ad
SainSmart 16-Channel 12V Relay Module Board for Arduino DSP AVR PIC ARM #adSainSmart #ad
- Indication lED's for Relay output status. Standard interface that can be controlled directly by microcontroller Arduino, PIC, ARM, MSP433, ARM, 8051, AVR, DSP, TTL logic.
12v 16-channel relay interface board, and each one needs 15-20mA Driver Current. Equipped with high-current relay, AC250V 10A ; DC30V 12A.
|Manufacturer||SainStore Inc. #ad|
2. AEDIKO #ad
AEDIKO 2pcs 8 Channel Relay Module DC 12V Relay Board Compatible with Arduino UNO R3 MEGA 1280 DSP ARM PIC AVR STM32 Raspberry Pi #adAEDIKO #ad
- 8 channel relay module voltage : 12v; normally open interfaces Maximum Load : AC 250V/10A, DC 30V/10A. 8 channel module equipped with screwed terminal plate and Fixed Bolt Holes, Standard Interface Can Connect With Microcontrollers and be Controlled by a Wide Range of Microcontrollers.
Relay module designed with fault-tolerant, even If The Control Line Breaks, the relay will Not Move; With Optical Coupling Isolation, Triggering More Reliable and Stable.8
8 channel relay module 12v comes with High-Current Relay, Trigger Current : 5mA. 12v relay module is 8 channel isolated, each Relay Can Individually Switch On/Off by An Opto-Isolated Digital Input.
3. UCTRONICS #ad
GPS, UCTRONICS DC 12V Time Delay Relay Module for Smart Home, Tachograph, Electronic Experiment, Industrial Control, Arduino Robot, PLC Control #adUCTRONICS #ad
- Search for asin b08tqty8mp to get the module with protective case. Operating current: 42ma; max. Load current: 10A. Functions: supports on delay and off delay modes, the delay time can be adjusted from 01s to 1h, the delay mode and delay time can be set by shorting or opening the jumper pins and rotating the potentiometer.
Self protection: built with protection against reversal diode, supports anti-reverse protection.
Load voltage: terminal nc is dc 30v or ac 250v, terminal NO is DC 28V or AC 125V; Max. Note: please remove the jumper cap of s5 when controlling AC current or DC current voltages other than 12V, otherwise the module will be burned or will not work properly.
Applications: this module works as a switch with time delay on and off function, DC motors, highly recommended for automotive circuit modification, and LED lights, pump and smart home control system. Operating voltage: dc 12v; quiescent current: 5. 5ma; max.
4. Oiyagai #ad
Oiyagai 5pcs 5V 1 Channel Relay Module Low Level Trigger Relay Board for Arduino ARM PIC AVR MCU with LED Indicator Light #adOiyagai #ad
- With the power supply and relay instructions, pull off, disconnect does not shine. Blue kf301 terminals to the control line is more convenient. The control dc or ac signal, you can control 220V AC load.
The module complies with international safety standards, the control area and the load region isolation trench. There is a normally open and one normally closed contact.
5. DollaTek #ad
DollaTek 5Pcs NE555 12V DC Adjustable 0-10 Second Timer Delay Relay Switch Module Shield for Arduino Raspberry Pi #adDollaTek #ad
- Useful for applications in equipment-delay to prevent sudden high current which can burn components and devices. Max. Loading:2200W. With power indicator LED red and trigger indication LED blue.
Output is voltage free & can be connected up to 10A load. Input voltage:DC12V. Stream with relay protection. Chrono-potentiometer regulation time delay, adjustable from 0 to 10 seconds by default.
6. SainSmart #ad
SainSmart 4-Channel Relay Module #adSainSmart #ad
- 5v 4-channel relay interface board, and each one needs 15-20mA Driver Current. Standard interface that can be controlled directly by microcontroller Arduino, PIC, AVR, 8051, DSP, MSP431, ARM, ARM, TTL logic.
Equipped with high-current relay, AC250V 10A ; DC30V 10A. Indication lED's for Relay output status.
|Manufacturer||SainStore Inc. #ad|
7. SunFounder #ad
SunFounder 4 Channel 5V Relay Shield Module Compatible with Arduino R3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi #adSunFounder #ad
- Equiped with high-current relay, AC250V 10A ; DC30V 10A. Indication led’s for Relay output status. 5v 4-channel relay interface board, and each one needs 15-20mA Driver Current.
Standard interface that can be controlled directly by microcontroller Compatible with Arduino, 8051, PIC, AVR, ARM, MSP430, ARM, DSP, TTL logic.
8. Aubric #ad
12V Relay Remote Switch Wireless RF Remote Control Switch 4 Channel Relay Module 433Mhz Transmitter Receiver Kit Universal Remote Controller for Lights Ceiling Fan Garage Door Opener Gate Car & More #adAubric #ad
- 2. The power input voltage is 12v, and each receiver’s relay capacity is up to [email protected]
and [email protected]
4. 3. 4 independent relay channels can either work together in latching for polarity reversing or individually in pulse / momentary, such as two channels for garage door controller motor, hold / hold to control different electronics, the other two for entry lights.
1. 5. Home automation security relay - learning code of 433mhz wireless transmission module has high-level security for its low repetitive rate and re-learn mode, by which it can delete the old code and re-learn a new code when a remote control get lost, so you are always in control of it. Wireless remote control kits - the dc 12 volt relay switch is equipped with 4 channel wireless receiver that built with high stability, floors and doors, steadily control receiver from any place within a reliable distance, security and performance.
Remote relay with 3 modes of operation – use a jumper to configure 3 modes of operating selection pulse / toggle and latching mode. Wide applications – the wireless remote control switch can be widely used in short and long range turn devices on / off wirelessly, electric generator, garage door openers, anti-theft alarm control panels, windows, trucks, RVs, electric door release locks, roller blinds, gate barriers, motorcycles, motor-driven curtain, LED lighting lamp bulbs and strips, cars, manual switches extender, boats, lifts, vehicles, entrance and access control etc.
Easy and flexible switch relay – the wireless relay kit is a perfect remote switch for those hobbyists with home automation DIY projects or business Industrial electrical. While the included 2 remote controls transmit strong signal that can pass through walls, max range up to 164ft/50m with no obstacle.
9. Huayao #ad
Huayao 2pcs 4 Channel DC 5V Relay Module with Optocoupler for UNO R3 MEGA 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi #adHuayao #ad
- Standard interface can be directly connected with microcontrollers. It is also able to control various appliances and other equipments with large current. 4-channel relay interface board, arm, which can be controlled directly by a wide range of microcontrollers such as AVR, PLC, PIC, etc.
Widely used for all mcu control, PLC control, industrial sector, smart home control. Working status indicator lights are conducive to the safe use. Relay output maximum contact is AC250V 10A and DC30V 10A. This relay module is 5v active low.