As an Amazon Associate I earn from qualifying purchases.
Gowoops #ad - The characteristics of ecological uSB supporting in Atmega32u4 can also make Micro board for Arduino to simulate mouse and keyboard, greatly improving the application. Micro board for arduino has 20 input output pins7 PWM output and 12 analog input.
SparkFun #ad - Dimensions: 1. 3in x 07in. Atmega32u4 running at 5v/16MHz Supported under Arduino IDE v1. 01+. 12x digital i/os 5 are PWM capable. Pth pads w/ Castellated Edges.
Has onboard Reset Button. Improved version of the sparkfun pro micro. The atmega32u4 can have the bootloader overwritten if not used properly. There is a way to fix the bootloader if needed and instructions are available online.
Deegoo #ad - The power source is automatically selected to the highest voltage source. Usage: the nano is 100% compatible with Arduino, with the same chips ATmega328P and CH340 with the official version. It has everything that arduino/Genuino UNO has electrically with more analog input pins and onboard +5V AREF jumper.
More breadboard space:nano's got the breadboard-ability of the Boarduino and the Mini+USB with smaller footprint than either, power and ground on the other. Http://sparks.
Small arduino uno board:it is a smallest, gnd on one top, atn, rx, so users have more breadboard space. Specification:the nano can be powered via the mini-b usb connection, 7-12v unregulated external power supply pin 30, or 5V regulated external power supply pin 27. If you need an older driver, pls get it from github—please read the link that follows immediate. Drivers: directly from the chip manufacturer: WCH 340 product home page: http://www.
Teyleten Robot #ad - 12 x digital i/os 5 are PWM capable. Atmega 32u4 au running at 5v/16mhz, supported under IDE v1. 01. 4 x 10-bit aDC pins. On-board micro-USB connector for programming. Rx and tx hardware Serial Connections.
HiLetgo #ad - Scm system can be completed within a file MicroSD card. Support micro sd card, Micro SDHC card high speed card. The module microsd card adapter is a Micro SD card reader module for reading and writing through the file system and the SPI interface driver.
3. 3v regulator circuit: ldo regulator output 3. 3v for level conversion chip, Micro SD card supply. Positioning holes: 4 m2 screws positioning holes with a diameter of 2.
HiLetgo #ad - Pin definition: dtr, tx, cts, rxd, VCC, GND. Rxd/txd transceiver communication indicator, with 500MA self-restore Fuse. Chipset: ft232rl, not genuine ftdi chip, Working Voltage: 3. 3v/5. 5v. Support win95/98/98se/me/2000/xp/win7 32bit 64bit /Vsita/, do not Support Win8.
MakerFocus #ad - When using it, please make sure that the GPS module is in an open location. With a usb interface, the default distribution of active antenna, you can directly use the phone data cable on the computer point of view positioning effect; With IPEX antenna interface, can be quickly positioned.
Note: this gps module will not search for signals when the weather is bad, and it will not search for stars indoors. Gpsbaud needs to be set to 9600 instead of 4800; pps pin is not needed unless using the gps to drive a hardware high precision clock; GT-U7 main module GPS module using the original UBLOX 7th generation chip, low power consumption, Software is compatible with NEO-6M.
Gt-u7 module, miniaturization, with high sensitivity, its extremely high tracking sensitivity greatly expanded its positioning of the coverage. How to use the gps module better, the link is obtained in the Product guides and documents, please download it before use. Usb directly connected to the computer, with the host computer-owned serial port function, no need for external serial module, That is, send IPX interface active antenna!.
ELEGOO #ad - We have always cared about the customer experience and improve the product function details. 100% compatible with the Arduino IDE and RoHS Compliant. Clear prints on the female header connector, more precise and easier to use the wire.
1. Gowoops
#adLeonardo Mini Controller 5V 16 MHz ATmega32u4 Module, Gowoops 2 PCS of Micro Board for Arduino
#adMore information #ad
Due to super small zise, Micro board for Arduino is intergrated to mini breadboard very easily. Owning to atemga32u4, micro board for Arduino can realize USB communications. Micro board for arduino is a mini controller based on Atmega32U4.| Brand | Gowoops #ad |
| Manufacturer | Gowoops #ad |
| Height | 1.2 Inches |
| Length | 8 Inches |
| Width | 4.2 Inches |
| Part Number | DBAD200100 |
| Model | LYSB01IGQE258-ELECTRNCS |
More information #ad
2. SparkFun
#adCompatible with Arduino development board 5V/16MHz microcontroller AP2112 3.3V Voltage Regulator Castellated PTH pin pads Reset button Maximum 6V input, USB-C ATmega32U4, SparkFun Qwiic Pro Micro
#adHas onboard Reset Button. Improved version of the sparkfun pro micro. The atmega32u4 can have the bootloader overwritten if not used properly. There is a way to fix the bootloader if needed and instructions are available online.
More information #ad
Rx and tx, qwiic connector for I2C, and SPI. Includes reset button, 9x 10-bit ADC pins. Small compatible with arduino board. Includes uart i. E. Usb drivers may be needed to be installed on a computer to communicate with the board. Input maximum of 6V. On-board usb-c connector for programming. Hardware serial connections. Ap2112 3. 3v voltage Regulator.| Brand | SparkFun #ad |
| Manufacturer | SparkFun Electronics #ad |
| Height | 0.59 Inches |
| Length | 1.3 Inches |
| Width | 0.7 Inches |
| Part Number | DEV-15795 |
More information #ad
3. Deegoo
#adMini Nano V3.0 ATmega328P Microcontroller Board w/USB Cable for Arduino
#adMore breadboard space:nano's got the breadboard-ability of the Boarduino and the Mini+USB with smaller footprint than either, power and ground on the other. Http://sparks.
More information #ad
Gogo. Co. Nz/ch340 Html; more detals on how to use it please refer to: http://audiodiwhy. Blogspot. Com/2018/05/one-cheap-arduino-nano-clone-o-plus-one. Html. Attention:before running the procedure, pls install the corresponding computer system driver. Small arduino uno board:it is a smallest, gnd on one top, atn, rx, so users have more breadboard space. Specification:the nano can be powered via the mini-b usb connection, 7-12v unregulated external power supply pin 30, or 5V regulated external power supply pin 27. If you need an older driver, pls get it from github—please read the link that follows immediate. Drivers: directly from the chip manufacturer: WCH 340 product home page: http://www.
| Brand | Deegoo #ad |
| Manufacturer | Deegoo #ad |
| Part Number | Mini Nano V3.0 ATmega328P |
More information #ad
4. Teyleten Robot
#adTeyleten Robot Pro Micro Atmega32U4 5V 16MHz Module Board Micro USB Pro Micro Development Board Microcontroller 3pcs
#adMore information #ad
| Brand | Teyleten Robot #ad |
| Manufacturer | Teyleten Robot #ad |
| Height | 0.59 Inches |
| Length | 1.3 Inches |
| Width | 0 Inches |
| Part Number | F25 |
More information #ad
5. HiLetgo
#adHiLetgo 5pcs Micro SD TF Card Adater Reader Module 6Pin SPI Interface Driver Module with chip Level Conversion for Arduino UNO R3 MEGA 2560 Due
#ad3. 3v regulator circuit: ldo regulator output 3. 3v for level conversion chip, Micro SD card supply. Positioning holes: 4 m2 screws positioning holes with a diameter of 2.
More information #ad
2mm, so the module is easy to install positioning, to achieve inter-module combination. Level conversion circuit: micro sd card to signal the direction of converts 3. 3v, microsd card interface to control the direction of the MISO signal is also converted to 3. 3v, general avR microcontroller systems can read the signal.| Brand | HiLetgo #ad |
| Manufacturer | HiLetgo® #ad |
| Weight | 0.11 Pounds |
| Part Number | 3-01-0038-5PCS |
| Model | 3-01-0038-5PCS |
More information #ad
6. HiLetgo
#adHiLetgo FT232RL FTDI Mini USB to TTL Serial Converter Adapter Module 3.3V 5.5V FT232R Breakout FT232RL USB to Serial Mini USB to TTL Adapter Board for Arduino
#adMore information #ad
| Brand | HiLetgo #ad |
| Manufacturer | HiLetgo #ad |
| Height | 4 Inches |
| Length | 6 Inches |
| Width | 0.5 Inches |
| Part Number | 3-01-0661-1 |
| Model | 3-01-0661-1 |
More information #ad
7. MakerFocus
#adDrone Microcontroller GPS Receiver Compatible with 51 Microcontroller STM32 Ar duino UNO R3 with IPEX Antenna High Sensitivity for Navigation Satellite Positioning, GPS Module GPS NEO-6MAr duino GPS
#adNote: this gps module will not search for signals when the weather is bad, and it will not search for stars indoors. Gpsbaud needs to be set to 9600 instead of 4800; pps pin is not needed unless using the gps to drive a hardware high precision clock; GT-U7 main module GPS module using the original UBLOX 7th generation chip, low power consumption, Software is compatible with NEO-6M.
More information #ad
Gt-u7 module, miniaturization, with high sensitivity, its extremely high tracking sensitivity greatly expanded its positioning of the coverage. How to use the gps module better, the link is obtained in the Product guides and documents, please download it before use. Usb directly connected to the computer, with the host computer-owned serial port function, no need for external serial module, That is, send IPX interface active antenna!.
| Brand | MakerFocus #ad |
| Manufacturer | MakerFocus #ad |
| Height | 0.39 Inches |
| Length | 1.09 Inches |
| Weight | 0.02 Pounds |
| Width | 3.94 Inches |
| Part Number | SN12SF83QOH11452IC |
| Model | SN12SF83QOH11452IC |
More information #ad
8. ELEGOO
#adELEGOO UNO R3 Board ATmega328P with USB CableArduino-Compatible for Arduino
#adMore information #ad
The elegoo uno r3 board now uses an 16u2 instead of the ATMega8U2 chip. Control using atmel atmega+328p chipthe same with Arduino UNO R3. Faster transfer rates and more memory.| Brand | ELEGOO #ad |
| Manufacturer | ELEGOO #ad |
| Height | 0.39 Inches |
| Length | 3.15 Inches |
| Weight | 0.06 Pounds |
| Width | 2.36 Inches |
| Part Number | EL-CB-001 |
| Model | EL-CB-001 |
| Warranty | 6 MONTHS |
More information #ad
