As an Amazon Associate I earn from qualifying purchases.
1. TIMESETL #ad
TIMESETL 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Electric Projects #adTIMESETL #ad
- Easy to use no assembly required. Parameter external size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge. Wide usage great for for arduino diy smart car robot power uno mega r3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits.
High efficient double h bridge design, one 4-phase stepper motor or two DC motors, can drive one 2-phase stepper motor, high efficient.
Just wire up motors and power, easy to use. This l298n board comes ready to go. High quality main driver chip l298n, strong driving ability, low calorific value, strong anti-interference, afterflow diode protection, more stable and reliable for Arduino projects.
|Model||L298N motor controller|
2. ILS. #ad
ILS, DC 12V-36V 500W High Power Brushless Motor Controller Driver Board Assembled No Hall #adILS. #ad
- Package included: 1 x dc 12v-36v 500w high Power Brushless Motor Controller Driver Board Assembled No Hall. Voltage range: 12V-36V. Drive power: ≤ 500W related working voltage. Drive plate type: JYQD_V6. 3e1. Size: 63 x 43 x 17mm.
|Manufacturer||I LOVE SHOPPING #ad|
3. Ximimark #ad
Ximimark L298P Shield R3 DC Motor Driver Module 2A H-Bridge 2 Way for Arduino UNO 2560 1 Pcs #adXimimark #ad
- The motor shield is based on the l298, solenoids, which is a dual full-bridge driver designed to drive inductive loads such as relays, DC and stepping motors.
If you are not satisfied with your purchase for any reason, Please Feel Free To Contact Us at the Buyer Center or Support Email, 24/7 Quick Reply.
Motor controller l298p, Drives 2 DC motors or 1 stepper motor. You can also measure the motor current absorption of each motor, among other features. It lets you drive two dc motors with your board, controlling the speed and direction of each one independently. Package: 1pcs Motor Driver Module.
4. KNACRO #ad
KNACRO PWM DC Motor Driver 60A DC 12V 24V 36V 48V 10-50V Forward Reverse Switch Tachometer Brush Motor Inverted Module Maximum Power 3000W #adKNACRO #ad
- Input voltage: dc 10-55V. Output voltage: Load Linear. Input current: require large than the motor operating current. Output Current: determine load size. Continuous current: 60A within.
Maximum power: 3000W. Knob hole: 7mm. Speed type: modulated current. Speed mode: on \ ofF linear potentiometer 270 degrees. Speed range: 0-100%. Operating frequency: 15KHZ. Terminal Type: Pressure riveting line terminal.
5. DFROBOT #ad
DFRobot MDV 2x2A DC Motor Controller for Arduino L298N #adDFROBOT #ad
- It can bear larger current due to the increased heat-sink dissipation. This breakout module with standard screw holes will help on applications and devices with flat spaces, so you don't need to use the Arduino stacked up shield.
It is able to be controlled by Arduino. It is easy to control, using a outstanding high-power motor driver chip, the L298N.
This mdv motor driver is able to drive 2 dc motors with voltage from 4. 8 to 46v, each motor can have the current up to 2A. This chip allows for direct drive of two bi-directional DC motors, and incorporates high-speed short diodes for protection.
6. LAFVIN #ad
LAFVIN 5 Sets 28BYJ-48 ULN2003 5V Stepper Motor + ULN2003 Driver Board for Arduino #adLAFVIN #ad
- Package content: 5 set 28byj-48 stepper motor + Uln2003 Driver Board +20pcs female to male Dupont cable as a gift. Stepper motor with a standard interface. Drive module board sizein: 1. 37*1. 18*06 ; stepper Motor diameter: 1.
06in ; stepper Motor lines: 9. 45in. A, b, c, d four-phase led indicates the status of the stepper motor work. 5 line 4 phase can be used for ordinary uln2003 chip driver, support the development board，With convenient use, connect to the 2 phase, direct docking.
7. KeeYees #ad
KeeYees L298N Motor Drive Controller Board Stepper Motor Control Module Dual H-Bridge with DC Motor and Smart Car Wheel Compatible with Arduino #adKeeYees #ad
- This is a good parts kit for an arduino and raspberry pi based RC car project. It has the strong driving ability, low calorific value and strong anti-interference ability.
It not only comes with 4pcs wheels and motors, but also 2pcs motor drive modules and 60pcs jumper wires, which are very useful accessories for your project. Motor drive controller: l298n used as the main driver chip.
Smart car wheels: the wheels are made of high-strength plastic and the tires are made of durable black rubber. To avoid damage the voltage stabilizing chip of Motor Drive Module, please use an external 5V logic supply when using more than 12V driving voltage. Tt motor: the motor is a two-axis motor with a reduction ratio of 1:48, which has strong anti-interference ability.
8. LGDehome #ad
10PCS DC 5V-36V 15AMax 30A 400W Dual High-Power MOS Transistor Driving Controller Module FET Trigger Switch Drive Board 0-20KHz PWM Electronic Switch Control Board DC Motor Speed Controller #adLGDehome #ad
- Operating voltage: dc dc 5v--36v; continuous current 15A at normal temperature; power: 400W; The maximum current can reach 30A under auxiliary cooling conditions. Wide voltage, support pwm;easily control high-power devices;service life: unlimited switch; working temperature: -40-85 ¡ã C; size: 1.
34x07x05inch/3. 4 x 1. 7 x1. 2cml*w*H. It can input pwm, dc motor, leD strip, lamp brightness, control motor speed, bulb, etc.
Trigger signal source: digital high and low level dc3. 3v--20v, etc. Can be connected to pwm signal, dc power supply, PLC interface, can be connected to single-chip IO port, signal frequency 0--20KHZ support.
Application: the output can control high-power equipment, micro pump, motor, solenoid valve, etc. Adopt imported dual mos parallel active output, large current, lower internal resistance, 15A, strong power, 400W at room temperature, meeting the needs of most equipment.