1. DAOKI
#ad
DAOKI 5 PCS L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560
#adDAOKI #ad - Driving dc motor because the module is drived by double H bridge, it can drive two motors simultaneously. The connecting method is shown inbelow figure after enable ENA ENB.More information #ad
Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled. Package included - 5 pcs L298N Motor Driver Controller Board Modules. The signal is shown in the figure.Brand | DAOKI #ad |
Manufacturer | DAOKI #ad |
Part Number | FBA_TS-US-078-SNL |
Model | FBA_TS-US-078-SNL |
More information #ad
2. TIMESETL
#ad
TIMESETL 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Electric Projects
#adTIMESETL #ad - High efficient double h bridge design, one 4-phase stepper motor or two DC motors, can drive one 2-phase stepper motor, high efficient. This l298n board comes ready to go.Just wire up motors and power, easy to use. Easy to use no assembly required. Parameter external size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge. High quality main driver chip l298n, strong anti-interference, afterflow diode protection, low calorific value, strong driving ability, more stable and reliable for Arduino projects.
More information #ad
Wide usage great for for arduino diy smart car robot power uno mega r3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits.Brand | TIMESETL #ad |
Manufacturer | TIMESETL #ad |
Height | 1.18 Inches |
Length | 5.91 Inches |
Width | 3.15 Inches |
Part Number | TXJ-061-US |
Model | L298N motor controller |
More information #ad
3. PChero
#ad
Dual H Bridge DC Stepper For Arduino Smart Car Robot, PChero L298N Motor Drive Controller Board Module
#adPChero #ad - This l298n board comes ready to go. Large current can reach 3A MAX and continue current is 2A. Just wire up motors and power, this thing will work wonders. Package included - 1pcs L298N Motor Driver Controller Board Modules.Easy of use - no assembly required. Item size - external size 43*43*27mm / 1. 69*1. 69*1. 06 inch. High efficiency - dual-channel h-bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.
More information #ad
High quality - use l298n as the main driving chip, strong anti-interference and low calorific value. Power to 25w. Note: to avoid damage, please use an external 5V logic supply when using more than 12V driving voltage. Drive voltage 5v-35v, high working power to 46v. And it also use large-capacity filter capacitor and diode with freewheeling protection function, so the module has such features as strong driving ability, thereby improve the reliability of module.
Brand | PChero #ad |
Manufacturer | PChero #ad |
Part Number | iS017*1 |
More information #ad
4. MELIFE
#ad
MELIFE 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Smart Car Power UNO MEGA R3 Mega2560
#adMELIFE #ad - Great for arduino diy smart car robot power uno mega r3 mega2560 duemilanove. Double h bridge design, one 4-phase stepper motor or two DC motors, can drive one 2-phase stepper motor, high efficient.This l298n board comes ready to go. Just wire up motors and power, easy to use. Main driver chip l298n, strong anti-interference, strong driving ability, low calorific value, afterflow diode protection, more stable and reliable for Arduino projects.
More information #ad
No assembly required. External size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge. If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits.Brand | MELIFE #ad |
Manufacturer | MELIFE #ad |
Part Number | 15489 |
More information #ad
5. DGZZI
#ad
DGZZI 2Set 28BYJ-48 DC 5V Geared Stepper Motor + ULN2003 Driver Test Module Board for Arduino
#adDGZZI #ad - Package includes: 2* 28byj-48 stepper Motor + 2* Uln2003 Driver Board. Uln2003 chip driver, with convenient use, support the development board, connect to the 2 phase, direct docking.More information #ad
5 line 4 phase can be used for ordinary. A, b, c, d four-phase led indicates the status of the stepper motor work. Stepper motor with a standard interface, when used directly pluggable.Brand | DGZZI #ad |
Manufacturer | DGZZI #ad |
Part Number | 2848-2003-2S |
More information #ad
6. Cytron
#ad
5-26V, 0.8A Bi-directional dual channel DC Motor Driver L298P Shield for Arduino
#adCytron #ad - Bi-directional control of two DC brush motor. Pin 4, 5, 6, 7 are used to drive two DC motor. Up to 2a current each channel. Motor driven voltage?6. 5 to 12vdcvin power Supply, 5. 0 to 26vdc external Power Source. Logic control, 5V from Arduino main board.More information #ad
Brand | Cytron #ad |
Manufacturer | Cytron Technologies #ad |
Height | 0.94 Inches |
Length | 2.68 Inches |
Weight | 0.07 Pounds |
Width | 2.17 Inches |
Part Number | 36011218 |
Model | SHIELD-2AMOTOR |
More information #ad
7. KNACRO
#ad
KNACRO L298P Motor Driver Module High-Power Dual H-Bridge Driver Shield DC Motor Drive Module Expansion Board for Arduino
#adKNACRO #ad - Stack design can be directly plugged into the Arduino, easier to use. Adopt dedicated high-power motor driver chip L298P which can directly drive two DC motors with drive current up to 2A.More information #ad
The l298p shield dc motor driver has PWM speed control mode; dual high-power H-bridge driver. Driven part of the input voltage vs: vin input 6. 5 ~ 12v, pwrin 4. 8 ~ 35v input. Use eight high-speed Schottky diodes at motor output as protection.Brand | KNACRO #ad |
Manufacturer | KNACRO #ad |
Part Number | L298P |
More information #ad
8. Longruner
#ad
Longruner 5X Geared Stepper Motor 28byj 48 Uln2003 5v Stepper Motor Uln2003 Driver Board with ArduinoIDE no Wire
#adLongruner #ad - Stepper motor with a standard interface. Stepping angle: 5. 625 x 1/64. Reduction ratio: 1/6. Drive module Board Size:1. 26 inchsX1. 38inchs. Good after-sales service. Cable length: about 20cm /8-inch.More information #ad
Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board. 5pcs stepper motor and driver board compatible with 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi. A, b, c, d four-phase led indicates the status of the stepper motor work. Motor diameter: 1. 1 inches. Wire length:9. 05 inchs.Brand | Longruner #ad |
Manufacturer | Longruner #ad |
Part Number | LK67 |
Model | LK67 |
Warranty | 1 year warranty |
More information #ad