Top 10 Stepper Motor Controller – Single Board Computers

As an Amazon Associate I earn from qualifying purchases.

1. TIMESETL

#ad

TIMESETL 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Electric Projects

#ad
TIMESETL #ad - Wide usage great for for arduino diy smart car robot power uno mega r3 Mega2560 Duemilanove, if driving voltage is more than 12V, use external standard 5volt TTL outputs to switch the H-bridge circuits.

High quality main driver chip l298n, afterflow diode protection, strong driving ability, low calorific value, strong anti-interference, more stable and reliable for Arduino projects. Easy to use no assembly required. This l298n board comes ready to go. Parameter external size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge. Just wire up motors and power, easy to use. High efficient double h bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors, high efficient.
BrandTIMESETL #ad
ManufacturerTIMESETL #ad
Height1.18 Inches
Length5.91 Inches
Width3.15 Inches
Part NumberTXJ-061-EU
ModelL298N motor controller

2. Bicool

#ad

Up to 1/32 Microstepping,Use for 3D Printer,Sculpturing Machine etc, Stepper Motor HAT for Raspberry Pi 4B/3B+/2B/B+/Zero/W/WH/ and Jetson Nano,DRV8825 Motor Controller Drives Two Stepper Motors

#ad
Bicool #ad - Protection features: overcurrent protection ocp, thermal shutdown TSD, VM Undervoltage Lockout UVLO. Motor drive current: 2. 5a. Standard raspberry pi 40pin gpio extension header, Supports Raspberry Pi series boards and Jetson Nano.

Onboard dual drv8825 motor controller ic with built-in microstepping indexer, easy to use. Drives two stepper motors, drives two stepper motors, Up to 1/32 Microstepping. Onboard multi connector options for stepper motors in different specifications. Integrates 5v regulator, allows providing power to Raspberry Pi. Motor drive voltage: 8. 2v~28v. 6 available microstepping modes, 1/16-step, 1/4-step, and 1/32-step. Logic voltage: 3. 3v. Adjustable motor drive current via potentiometer, half-step, configured with the DIP switches: full-step, 1/8-step, maximum 2.5a current output.
BrandBicool #ad
ManufacturerBicool #ad
Part NumberStepper Motor HAT
ModelStepper Motor HAT

3. Usongshine

#ad

Usongshine DM542 Stepper Motor Controller Leadshine 2-Phase Digital Stepper Motor Driver 18-48 VDC Max. 4.2A for 57 86 Series Motor.

#ad
Usongshine #ad - 20khz chopping frequency. Low speed without vibration. H bridge bipolar constant phase flow subdivision driver. Precision electric casting control greatly reduces motor heating and halve the chattering automatically at rest.

Low noise. High segmentation: 2, 10, 4, 16, 8, 32, 64, 128, 50, 125, 256.5, 25, 200 In the harsh environment of the power grid, it had strong anti-interference ability, high-precision positioning and high reliability. Output current dip switch is adjustable. Optical isolation signal input, strong anti-interference ability with over voltage, over light and other protective functions. Suit for nema 17, 23 stepper motor,2-phase hybrid stepper motors Outer diameter: 57, 86mm.
BrandUsongshine #ad
ManufacturerUsongshine #ad

4. KeeYees

#ad

KeeYees L298N Motor Drive Controller Board Stepper Motor Control Module Dual H-Bridge with DC Motor and Smart Car Wheel Compatible with Arduino

#ad
KeeYees #ad - It not only comes with 4pcs wheels and motors, but also 2pcs motor drive modules and 60pcs jumper wires, which are very useful accessories for your project.

To avoid damage the voltage stabilizing chip of Motor Drive Module, please use an external 5V logic supply when using more than 12V driving voltage. Smart car wheels: the wheels are made of high-strength plastic and the tires are made of durable black rubber. This is a good parts kit for an arduino and raspberry pi based RC car project. Motor drive controller: l298n used as the main driver chip. It has the strong driving ability, low calorific value and strong anti-interference ability. Tt motor: the motor is a two-axis motor with a reduction ratio of 1:48, which has strong anti-interference ability.
BrandKeeYees #ad
ManufacturerKeeYees #ad

5. Longruner

#ad

Longruner 5X Geared Stepper Motor 28byj 48 Uln2003 5v Stepper Motor Uln2003 Driver Board with ArduinoIDE no Wire

#ad
Longruner #ad - Stepper motor with a standard interface. A, b, c, d four-phase led indicates the status of the stepper motor work. Stepping angle: 5. 625 x 1/64. Reduction ratio: 1/6. Drive module Board Size:1. 26 inchsX1. 38inchs. Cable length: about 20cm /8-inch. Motor diameter: 1. 1 inches. Wire length:9. 05 inchs. 5pcs stepper motor and driver board compatible with 2560 1280 DSP ARM PIC AVR STM32 Raspberry Pi. Good after-sales service. Great packing in a box : 5 set Uln2003 Stepper Motor + Driver Board.
BrandLongruner #ad
ManufacturerLongruner #ad
Part NumberLK67
ModelLK67
Warranty1 year warranty

6. DAOKI

#ad

DAOKI 2 PCS L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 with Dupont Cable

#ad
DAOKI #ad - Driving dc motor because the module is drived by double H bridge, it can drive two motors simultaneously. The connecting method is shown inbelow figure after enable ENA ENB. The signal is shown in the figure. Input the following driving timing from IN1-IN4 then the speed and direction of the stepper motor can be controlled. Package content: 2 x l298n motor drive controller board, 1 x 11. 8" male-female dupont cables 12 PIN, 1 x 11. 8" male-male dupont cables 12 PIN, 1 x 19. 6" 28awg wire.
BrandDAOKI #ad
ManufacturerDAOKI #ad
Part NumberDR-US-254
ModelDR-US-254

7. kuman

#ad

Red Blue, kuman CNC Shield Expansion Board V3.0 +UNO R3 Board + A4988 Stepper Motor Driver with Heatsink for Arduino Kits K75 CNC Shield+UNO R3+Stepper Motor K75-CNC-UK

#ad
kuman #ad - 4pcs a4988 stepper Motor Driver with radiator. Pwm spindle and direction pins. Latest cnc shield Version 3. 0 board. Mcu: atmega328, usb interface: ATmega16U2. 2 x end stops for each axis 6 in total. 4-axis support. Runs on 12-36V DC.
Brandkuman #ad
Manufacturerkuman #ad
Height2.36 Inches
Length1.97 Inches
Weight0 Pounds
Width1.57 Inches
Part NumberK75-CNC-UK
ModelK75-CNC-UK
Warranty1 year

8. MELIFE

#ad

MELIFE 5Pack L298N Stepper Motor Driver Controller Board Dual H Bridge Module for Arduino Smart Car Power UNO MEGA R3 Mega2560

#ad
MELIFE #ad - Main driver chip l298n, afterflow diode protection, strong anti-interference, strong driving ability, low calorific value, more stable and reliable for Arduino projects.

No assembly required. Double h bridge design, one 4-phase stepper motor or two DC motors, can drive one 2-phase stepper motor, high efficient. If driving voltage is more than 12V, please use external standard 5volt TTL outputs to switch the H-bridge circuits. Just wire up motors and power, easy to use. Great for arduino diy smart car robot power uno mega r3 mega2560 duemilanove. This l298n board comes ready to go. External size 43*43*27mm / 1. 69*1. 69*1. 06 inch, voltage 5v-35V, drive current 2A Max single bridge.
BrandMELIFE #ad
ManufacturerMELIFE #ad
Part Number15489

9. PIXNOR

#ad

PIXNOR 10pcs L293D DIP 16-pin IC Stepper Motor Drivers Controllers Black

#ad
PIXNOR #ad - Material: durable hard alloy and plastic. Enable facility. L293d dip 16-pin ic stepper Motor Drivers Controllers. Color: mainly black. Peak output current: 1. 2a channel non repetitive. Pin no: 16 pins. Over temperature protection. Channel capability: 600mA output current channel.
BrandPIXNOR #ad
ManufacturerPixnor #ad
Height0.91 Inches
Length1.31 Inches
Width1 Inches
Part Number112108A2NKL5005
Model4332013342

10. KINCREA

#ad

Stepper Motor 242 Items, MEGA 2560 R3 Controller Board, KINCREA Mega 2560 Project The Most Complete Ultimate Starter Kit Compatible with ArduinoIDE w/Tutorial, Servo, LCD 1602

#ad
KINCREA #ad - Total 242 items with clear list are packaged in a nice plastic box, meet your demands for your different projects either it is simple or complex. This kit can be used with mac, PC and Linux.

5v relay module make it easier to connect and control the high voltage. This is the most complete with arduinoide mega2560 starter kit with FREE tutorials, just follow our tutorials and you will come to start with ArduinoIDE. A clear listing for components can be viewed by clicking the picture or in the product description. The way to install driver can be referred to the product description. Mega 2560 controller board and expansion board are perfect for ArduinoIDE project with excellent product finish. Cd included detailed tutorials, you can also contact us by email to get documents.
BrandKINCREA #ad
ManufacturerKINCREA #ad
Part NumberUA003
ModelUA003
WarrantyNO